Determining the Percentage of Water in a Hydrate
Interactive heating-to-constant-mass investigation · Simulated laboratory data
Background Information
A hydrate is an ionic compound containing a definite number of water molecules within its crystal structure. Its formula is written as salt · nH₂O, where n is the number of water molecules per formula unit.
When an appropriate hydrate is heated, water may be released and a lower-mass anhydrous solid remains. Measuring the mass before and after heating allows us to determine the mass and amount of water lost.
Essential calculations
Mass of hydrate = (crucible + hydrate) − crucible
Mass of water = (crucible + hydrate) − (crucible + anhydrous salt)
Percentage water = (mass of water ÷ mass of hydrate) × 100%
Moles of water = mass of water ÷ 18.015 g mol⁻¹; moles of anhydrous salt = mass of anhydrous salt ÷ its molar mass.
Hydration number, n ≈ moles of water ÷ moles of anhydrous salt. Round only after considering measurement precision and whether the sample was fully dehydrated.
Why heat to constant mass?
Heating, cooling and weighing are repeated until successive masses differ by no more than a defined tolerance. This provides evidence that the removable water has been driven off. Overheating can cause decomposition or loss of solid, leading to incorrect results.
Model assumptions
The simulation models copper(II) sulfate pentahydrate, CuSO₄·5H₂O, which loses its water of crystallization on heating. The model uses an illustrative gradual dehydration curve and simulated balance readings; it is not a calibrated kinetic model or a substitute for laboratory observations.
Print or save the assignment, perform the virtual lab, record observations and complete your lab report.
Student Laboratory Assignment
Research question: What percentage by mass of copper(II) sulfate pentahydrate is water, and how can experimental mass measurements be used to determine its hydrate formula?
Learning goals
- Use repeated mass measurements to establish constant mass.
- Calculate mass percent, amount of substance and a hydrate mole ratio.
- Assess sources of uncertainty and distinguish incomplete dehydration from sample loss.
Required procedure
- Record the empty crucible mass and the initial crucible-plus-hydrate mass.
- Heat the sample, allow it to cool, then weigh it. Record at least three heating cycles.
- Continue heating until two successive post-heating masses differ by at most 0.005 g.
- Repeat the investigation using a different starting sample mass.
- Calculate percentage water and the water-to-salt mole ratio for each completed trial.
- Compare your experimental results with the theoretical composition and discuss limitations.
Virtual Heating Station
Select a sample mass and start a new trial.
Set up the experiment
The duration setting controls the model's dehydration progress, not real minutes. All weighing occurs after cooling.
Initial combined mass: 26.350 g
Constant-mass criterion: difference ≤ 0.005 g between successive heated masses.
Heating-cycle log
| Cycle | Mass after cooling (g) | Change (g) |
|---|
Do not record a completed trial until the constant-mass criterion has been met.
Data & Calculations
Completed trials are added only after constant mass is achieved. Each trial includes calculated mass percent and mole ratio.
| Trial | Hydrate (g) | Anhydrous (g) | Water (g) | Water (%) | n(H₂O)/n(CuSO₄) |
|---|
Heating curve — current trial
Theoretical water content of CuSO₄·5H₂O: 36.08% (using molar masses 159.61 and 18.015 g/mol).
Formal Laboratory Report
Type your responses below. They autosave in this browser. The report includes your recorded trials and calculation results when printed.
Results from recorded trials
Teacher Resources
Course: SCH3U — Grade 11 University Chemistry. Suggested assessment focus: stoichiometry, chemical formulas, experimental design, measurement, and evaluation.
Suggested KTCA rubric
| Category | Weight | Evidence |
|---|---|---|
| Knowledge & Understanding | 25% | Hydrate terminology and formula interpretation |
| Thinking & Investigation | 35% | Repeated heating, constant-mass criterion, reasoning |
| Communication | 20% | Tables, calculations, units, formal report |
| Application | 20% | Hydration-number calculation and uncertainty analysis |
Teacher reference values
CuSO₄ molar mass ≈ 159.61 g/mol; H₂O ≈ 18.015 g/mol; CuSO₄·5H₂O ≈ 249.685 g/mol; theoretical mass percentage water ≈ 36.08%. Expected molar ratio is approximately 5:1.
Scientific model limitations
Dehydration progress is idealized. The model assumes the solid is chemically stable under appropriate heating, no splattering, no decomposition, and perfect weighing to 0.001 g. Real copper(II) sulfate dehydration may occur in stages and requires safe supervised procedures.