1. Virtual Labs
  2. General Science
  3. Electricity & Circuit Investigation
⬇ Assignment (PDF)
WorksheetGalaxy / Virtual Science Laboratories

Electricity & Circuit Investigation

SNC1W · Grade 9 Science · Series and parallel circuits · Free interactive virtual laboratory

Background Information

Electric current (I, amperes) is the rate of flow of electric charge. Potential difference (V, volts) is energy transferred per unit charge. Resistance (R, ohms) describes opposition to current. Ohm's law for an ohmic resistor is V = IR.

Series circuits

One path for current. The same current flows through each resistor. Total resistance is R₁ + R₂; source voltage is divided between resistors.

Parallel circuits

Multiple paths for current. Each branch has the full source voltage. Branch currents add to the source current. For two resistors: 1/Rₜ = 1/R₁ + 1/R₂.

Power and energy

Electrical power: P = VI (watts). Electrical energy: E = Pt (joules), where t is time in seconds.

Model scope: ideal DC voltage source, ohmic resistors, negligible wire resistance, no internal battery resistance. Bulb symbols represent resistive loads, not realistic filament behaviour. Never build circuits using wall outlets; use only approved low-voltage classroom equipment under supervision.
Download student assignment (PDF)

Print or save the assignment, perform the virtual lab, record observations and complete your lab report.

Student Assignment

  1. Predict which circuit has greater total resistance when both loads are identical: series or parallel.
  2. Set the source to 6.0 V and both loads to 10 Ω. Record the calculated source current and each load's voltage and current in series.
  3. Switch to parallel without changing the source or loads. Record the new values.
  4. Hold the source voltage constant and change R₂ to 20 Ω, then 30 Ω. Record at least four trials.
  5. Use the graph to compare total current against total resistance. Explain the relationship.
  6. Calculate the energy used in 60 s for one trial, then compare with the simulation.
  7. Explain how a real battery, wires, or incandescent lamps might differ from this model.

Success criteria: identify series/parallel arrangements; use V = IR and P = VI; interpret measurements and a graph; explain limitations and electrical safety.

Virtual Circuit Bench

Choose a circuit arrangement and adjust the battery and two resistive loads. Values update immediately. Click Record trial to save a measurement.

The circuit is a schematic, not a wiring instruction. The simulated ammeter reads source current; the displayed branch values act as virtual voltmeter and ammeter readings.

Data & Graphs

Record at least four trials. Select a circuit type to graph its source current against total resistance; axes have physical units.

#TypeV source (V)R₁ (Ω)R₂ (Ω)R total (Ω)I source (A)V₁ (V)V₂ (V)I₁ (A)I₂ (A)P total (W)E (J)
No trials recorded yet.

Changing both source voltage and resistance between trials may obscure the relationship. Hold voltage constant when investigating I versus R.

Responses and trials autosave in this browser. Browser storage may be cleared; export a JSON backup if you need to keep your work.

Teacher Resources

Course: SNC1W, Grade 9 Science. Format: individual or paired virtual investigation, approximately 45–60 minutes.

Expected calculations at 6 V, R₁ = R₂ = 10 Ω

Series: Rₜ = 20 Ω; I = 0.30 A; V₁ = V₂ = 3.0 V; total P = 1.8 W.
Parallel: Rₜ = 5 Ω; source I = 1.20 A; I₁ = I₂ = 0.60 A; V₁ = V₂ = 6.0 V; total P = 7.2 W.

KTCA rubric (4-point scale)

CategoryEvidenceLevel 1Level 2Level 3Level 4
KnowledgeElectrical terms, series/parallel rulesLimitedSomeConsiderableThorough
ThinkingControls, predictions, data analysisLimitedSomeConsiderableHigh degree
CommunicationTables, graphs, explanationsLimited claritySome clarityClearHighly clear
ApplicationOhm's law, power, real-world limitsLimitedSomeConsiderableThorough

Discussion and safety

Clarify that resistors are ideal and the model does not simulate short circuits, heating, wire ratings, battery depletion, or actual bulb brightness. For classroom extension, measure only teacher-approved low-voltage circuits. Do not use household mains electricity.

Accessibility

All inputs are labelled; numeric readouts accompany diagrams. Graph values remain available in the data table. Students may complete the report without relying on colour.

More Grade 9 Science labs

Free interactive labs with printable assignments. All general science labs →

© WorksheetGalaxy · Free virtual science labsAll virtual labsSample lab reportAboutPrivacyContact